Macrame Belt with Square Buckle: Autumn Tweed

OK, a few of you asked how to macrame a “regular” belt with a square buckle. A belt that can go through belt loops.

Well, here it is.

Image Hosting by PictureTrail.com


Free Image Hosting at www.picturetrail.com Free Image Hosting at www.picturetrail.com Free Image Hosting at www.picturetrail.com Free Image Hosting at www.picturetrail.com


Supplies/Tools Needed:

  • 30 yards of 3 1/2mm braided macrame cord *
  • one square belt buckle with 1″ bar for mounting cords
  • craft glue
  • macrame board or covered ceiling tile
  • T-pins
  • scissors
  • yardstick, ruler, tape measure

Image Hosting by PictureTrail.com


Instructions to make Autumn Tweed Macrame Belt

Step 1.¬† Cut two cords 7 yards long and two cords 8 yards long. Cords will be mounted onto the 1″ bar end of the belt buckle in this order.

  • 7 yd cord (4 1/2 yds of it on the left and 2 1/2 yds of it on the right)
  • 8 yd cord (3 1/2 yds of it on the left and 4 1/2 yds of it on the right)
  • 8 yd cord (4 1/2 yds of it on the left and 3 1/2 yds of it on the right)
  • 7 yd cord (2 1/2 yds of it on the left and 4 1/2 yds of it on the left)

Image Hosting by PictureTrail.com

Step 2. Number cords 1-8.

Row 1. Tie Square Knots (SK) with cords 1-4 and 5-8.
Row 2. Tie one SK with cords 3-6.
Row 3. Tie SK’s with cords 1-4 and 5-8.

Image Hosting by PictureTrail.com

Repeat. Row 2. Row 3. Row 2. Row 3. Row 2. Row 3. Row 2. Last row should have ONE Square Knot. This is how your belt should look at this point.

Image Hosting by PictureTrail.com

Step 3.
Tie 2 SK’s with cords 1-4. One right under the other. Tie 2 SK’s with cords 5-8. One right under the other. Tie one SK with cords 3-6. See photo for help if needed. This step is creating “holes” along the belt’s length.

Image Hosting by PictureTrail.com

Step 4. Keep repeating Step 3 until you reach the desired waist length or until you reach 10″ from the SHORTEST cords.

Your last row before beginning the next step should have ONE SK.

Step 5. This step finishes off the end of the belt. You will be tying Diagonal Double Half Hitch knots (DDHH) onto a diagonal anchor cord.

Image Hosting by PictureTrail.com

Cord 1 is the right diagonal anchor cord for this step. Pin cord 1 to the board diagonally using a T-pin. Double Half Hitch cords 2-4 onto it. Start with cord 2. See photos for help. 1st photo is showing one half hitch. 2nd photo is showing a double half hitch.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

This is how cords 2-4 now look.

Image Hosting by PictureTrail.com

Step 6. Now you are going to repeat this on the right side using Cord 8 as the left diagonal anchor cord. Pin cord 8 to the board diagonally using a T-pin. Double Half Hitch cords 7-5 onto it. Start with cord 7 and work down to cord 5.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

This is how belt looks after completing one row of diagonal double half hitches on both left and right.

Image Hosting by PictureTrail.com

Step 7. Ready for DDHH Row 2? OK, repeat Step 6. Do exactly what you did. Everything. You can renumber the cords or just visually number them in your head. 4 cords on the right and 4 cords on the left. 1-4 and 5-8.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

2 Diagonal Double Half Hitched rows.

Image Hosting by PictureTrail.com

Step 8. Now you are ready for the 3rd row of DDHH’s. The last one. Yay!! Again, repeat Step 6.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

3 Diagonal Double Half Hitched rows completed.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

Step 9. One last thing to do. Make sure the last knots are tight. Cut the ends close but not too close. Save enough on the tip to melt and press down. Using matches, touch the cord for a nanosecond taking care not to burn or scorch the cord. Press down for a smooth edge.

I reinforced this area with sewing thread to make sure the knots on the tip will not work themselves undone when wearing. Make tiny stitches so they are not visible.

Add a bit of craft glue to the last row of knots on the tip, on the back side of the belt. Allow to dry.

Image Hosting by PictureTrail.com

All done!! Congratulations!! You are ready to wear your belt. Put it on. Use one of the “holes” created in Step 3 to strap it on. You can move it to any hole. Wear it tight, loose or however you wish. Enjoy!!

Image Hosting by PictureTrail.com


* Note: Yardage to use depends on what size you want. Adjust belt size by adding or subtracting yardage. Experiment.

It is always best to cut longer cords and not run short and have to start over. You can always use leftover cord for other projects.

This belt in the tutorial measures 37″ at the point where belt prong thingy inserts into the hole.


Need some HELP with tying knots?

In case you have forgotten how to tie a Square Knot (SK) or are new to macrame, here’s a picture of me beginning to tie one.

Image Hosting by PictureTrail.com

Also you can go here for help. Don’t be afraid. Try it. It’s easy!!

https://thisyearsdozen.wordpress.com/2008/05/06/how-to-tie-a-macrame-square-knot/

http://macrame_1.tripod.com/knots/ddhh.html