How To Make Wire Cages For Round Beads

Silly me!! Didn’t know I could make these cages myself.

I have been buying them!!

Image Hosting by PictureTrail.com

Making these wire cages is quite easy. I found the directions in one of my wire making craft books.

Creating Wire and Beaded Jewelry by Linda Jones.

It is turning out to be my most used wireworking resource.

Image Hosting by PictureTrail.com

My tutorial is based on the results from using 20 gauge wire. It is great practice wire and is forgiving in case you need to unbend, straighten and start over. It is also inexpensive. I got 8 yards for $2.50.


Instructions for making ONE Wire Cage to enclose a 12-14 mm round bead.

Step 1. Cut lengths of 14″ wire. One per wire cage.

Step 2. Making the Swirls. Start at the tip on one end and make a small bend with round nose pliers. (See photo at end of tutorial for tools used in this project.) Now switch to either chain nose pliers or flat nose pliers. Either one will be fine for this step.

Slowly start to form a circle by covering the tip loop with chain nose/flat nose pliers, bending the wire as you turn in as perfect a circle as you can. Make the swirl large enough to cover one side of the bead.

Now start on the other end of the wire. Repeat the same steps and make a swirl on the opposite end of the wire. Make sure the swirls look about even with the same number of revolutions. Leave about 2-2 1/2″ of wire between the swirls.

Image Hosting by PictureTrail.com

Step 3. Making the Hook. Using round nose pliers, find the center of the wire with the swirls facing downward. Hold tight and push up one side and then the other. Refer to photo illustration.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

You are making the “hook” that will serve two purposes. It will cover the center open area of the bead, forming a connection to the side swirls. The hook also creates a loop for attaching the stringing material of your choice.

Image Hosting by PictureTrail.com

Step 4. Enclosing the Bead. Fit one side swirl on top of the bead.

Image Hosting by PictureTrail.com

Now fit the other swirl on the opposite side of the bead, like a sandwich. Holding both swirls in place, wrap the hook around the center of the bead.

Image Hosting by PictureTrail.com

Press flat against the bead middle. Mold the wire, straightening as you work. Once you are satisfied with the cage and it covers your bead nicely, you are ready to bend up the tip of the hook to form a hanger.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

Step 5. That’s it!! You are done. Ready to add whatever you wish to hang your beaded wire cage from.


You can make cages smaller or larger by reducing or increasing the number of revolutions. Also experiment with different lengths of wire to see which best covers the bead size you are using.

Wire cages will look pretty on a pendant, bracelet or earrings. The book used jump rings to connect to the turned up hook. Even keychains would be fun to make. Load up with charms and beads. What better way to use up left over beads or beads with a few flaws. Won’t be able to see the flaw inside a wire cage!!

I am thinking you could make wire cages for other bead shapes too. Oblong and squares. By adjusting the design of the wire. Try experimenting to see what you can create. So far I have only made round cages but I plan to try making other shapes.

My beads I am making wire cages for are blue with orange stripes. I am going to work in seed beads in blue and orange somehow. Still working on that part.

Image Hosting by PictureTrail.com


Tools used: Round nose pliers, Chain nose pliers, and plastic covered Flat nose pliers.

Image Hosting by PictureTrail.com

Connecting Wire Squares, Making a Necklace

Thursday, July 17

Image Hosting by PictureTrail.com

Ever try to make a PERFECT square out of wire?

Not possible, at least for me. My edges are rounded no matter how carefully I bend the wire. And try as I might, I could not get two squares to come out exactly the same. I kept making them until I ran out of wire. I have to admit, the last few were much better than the first ones. So practice does make perfect.

My early intentions were to make a bracelet. I got quite a chuckle when I connected four of them with jump rings and draped them around my wrist. OK. So… On to Plan B. Hubby said it before I did. “They would make a nice necklace.”

I selected the best of the bunch, only discarding one. The rest ended up around my dummy’s chest and shoulders.

Image Hosting by PictureTrail.com

I added several links of chains and used lobster claw clasps on both sides to connect them. I love working with chain links. I bought a lot of it months ago but am just now starting to incorporate it into my designs.

Image Hosting by PictureTrail.com Image Hosting by PictureTrail.com

To make these squares, I used 12 gauge brown wire and followed a design found in one of my wire making craft books. I kind of improvised, making my squares slightly larger than the book.

Before making the larger squares, I first practiced with thinner 20 gauge wire.

Image Hosting by PictureTrail.com

The first one is laughable. But instead of tossing it, I kept it as a reminder that the “next” one should be better than the last. As you can see from my line up that is so true. Not sure what I will do with these squares made from 20 gauge. They are too thin to hold up in a permanent design. Great for practicing though.

So… what do you think?